ND-91763(E)
ISSUE 2.0
term
D PSIII
••••••••••••••••••••
USER GUIDE
Use
User Safety Protocol
•••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
Important: Read this information before using your PSIII
.
Follow the instruction below to use this products safely, to protect you and other people from possible injury, and
to protect properties. Improper use may cause heat, explosion, and fire.
DANGER
•
•
Recharge the battery pack with the matching battery charger.
The battery pack has polarity; positive (red wire) and negative (black wire). Make sure the polarity is correct when you insert the battery
pack into the phone.
•
•
Use the battery pack only for this telephone system. Do not use it with other electrical devices.
Keep the following warnings to protect the battery pack from heating, explosion, and fire.
•
•
•
•
Do not throw the battery pack into fire.
Do not solder the battery pack directly.
Do not short the positive (+) and negative (–) terminal of the battery pack with metal.
Do not poke the battery nor smash it with hammer.
•
•
Do not disassemble nor modify the battery pack. A damaged circuit may cause heat, explosion, and fire.
The internal liquid of the battery pack is strong acid. If the battery liquid gets into your eye, rinse your eye well with water and consult
with a doctor.
i
W
WARNING
•••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
•
•
Do not use, leave, nor recharge the battery pack near fire or under the direct sunlight. High temperature may damage the internal safety
circuit and may cause malfunction of the recharger, heat, explosion, or fire.
Do not use the units when you notice smoke, strange smell or other unusual happenings. It may cause fire if you continuously use them.
Turn off the power of the phone system immediately. For the recharger, disconnect the power plug immediately. Make sure that smoke is
ceased, and then contact the nearest NEC service office. Never attempt to repair such malfunctioning unit by yourself.
If you had an accident such as dropping the phone or broke the units, turn off the power of the phone system immediately. For the
recharger, disconnect the power plug immediately. Contact the nearest NEC service office. If you keep using such units, they may cause
fire or electrical shock.
•
•
•
If water smeared into the unit, turn off the power of the phone system immediately. For the recharger, disconnect the power plug
immediately. Contact the nearest NEC service office. If you keep using such units, they may cause fire or electrical shock.
Do not insert flammable or metal objects into the units. If a foreign object were accidently placed into the units, turn off the power of the
phone system and plug out the power adapter. Contact the nearest NEC service office. If you keep using such units, they may cause fire or
electrical shock. Pay special attention to children to protect from similar accidents.
•
•
Do not attempt to disassemble nor modify the units. It may cause fire, electrical shock, or system malfunction. Modification by a user is
prohibited by law.
Do not open the units intentionally. It may cause electrical shock or system mulfuction. Ask the nearest NEC service office test
adjustment, and repair of the units.
•
•
Do not twist, put a heavy object, nor push the phone system. Such actions may cause damage, fire, or injuries.
Do not place a container with water such as a vase, a plant pot, a cup, cosmetics, chemicals, nor a small metal object. Splashing water over
the units and foreign metal object inserted into the units may cause fire or electrical shock.
•
Do not use the unit in a high humid area such as a bath room or near a humidifier. They may cause fire, electrical shock, or system
malfunction.
•
•
Use the specified power adapter which is attached to the unit. Other adapters may cause fire or system malfunction.
Do not damage, or modify the power adapter cord. Do not kink, pull, twist, or bundle it. Do not put a heavy object or heat it. They may
cause fire, electrical shock, or system malfunction. Contact the nearest NEC service office for a damaged adapter cord.
Do not touch the power plug with a wet hand. It may cause electrical shock or system malfunction.
Do not touch the units or replace a battery with a wet hand. It may cause electrical shock or system malfunction.
Once you hear thunder during using the phone system outside, immediately stop using it and move to a safe place.
Do not use a multiple plugs. It may cause fire or electrical shock.
Follow the instruction below when you use a battery pack. They may cause heating, explosion, and fire:
Do not put the battery pack into a microwave oven or a pressure chamber.
Do not use other batteries with this battery pack.
•
•
•
•
•
•
•
•
If the internal battery liquid is clung to your skin or clothes, immediately rinse it with clean water to prevent chemical damage to your skin
and clothe.
•
Do not use the phone or recharge the battery in a place where fire or explosion may occur.
ii
WARNING
•••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
•
This phone system dose not have explosion protection. Do not use it where a flammable gas such as propane and gasoline are stored. Turn
off the power of the phone immediately. Do not recharge the battery in such a place.
iii
Table of Contents
•••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
USER SAFETY PROTOCOL
CONFIRMATION TONE
21
22
23
23
24
25
26
26
27
28
29
30
31
36
37
38
38
40
40
41
42
43
45
46
47
48
49
51
KEY CLICK
WARNING
KEY LIGHT
THE BASICS
LED FLASH
DISPLAYS AND KEYS
THE PSIII DISPLAY
CHARGING THE BATTERY
REPLACING THE BATTERY
2
3
4
5
PROGRAM SOFTKEYS
TO
SET VM (VOICE MAIL) NUMBER
MESSAGE STORAGE
PROTECT TMM (TEXT MAIL MESSAGE)
TM REMINDER
BASIC OPERATIONS
TO
TO
TO
TO
TO
TO
TO
TO
TO
TO
TURN THE PHONE
O
N
6
6
TO
ADJUST RING VOLUME
ORIGINATE A CALL
RECEIVE A CALL
SPEAKER RING
STATION RING
7
USE LAST NUMBER REDIAL
USE SPEED DIAL
8
T
O
O
SET CALL FORWARDING
8
T
SET CALL FORWARDING DESTINATION
USE CALLING PARTY NUMBER
TRANSFER A CALL
9
TIME DISPLAY
10
10
10
11
11
11
TO
TO
TO
SETUP TIME
PLACE A CALL
ON-HOLD
ENTRY NAME
USE COURTESY MODE
ADJUST BRIGHTNESS
KEYPAD LOCK
NO SERVICE
MISSED CALL
HEADSET RING
AUTOMATIC ANSWER
ANSWER TONE
PASSWORD
PSIII FUNCTIONS
TO
TO
TO
TO
TO
TO
ENTER NAMES IN THE DIRECTORY
ENTER SPEED DIAL NUMBERS
ACCESS VM (VOICE MAIL)
15
16
17
18
19
19
20
PROTECT DIRECTORY
DEFAULT SET
RESET ALL
REVIEW TM (TEXT MESSAGE)
ADJUST CALL VOLUME
ACCESS SOFTKEYS
TO
USE CALL FORWARDING
USE INCOMING CALL VIBRATION NOTIFICATION
PHONE
NO.
SERVICE ALARM
THE BASICS
••••••••••••••••••••••••••••••••••••
DISPLAYS AND KEYS
Fixed, Snub-Nose Antenna.
No need to pull out or adjust.
LED Ring Indicator
Red light indicates incoming call.
L1 Button
Press to originate or answer a call.
L2 Button*
LCD (Liquid Crystal Display)
Headset Jack
Press to originate or answer a call on the second
line.
FNC (function) and Scroll Key
Q (FNC Key)
Press to activate numerous telephone functions.
STWX(Scroll Key)
L1
L2
END/PWR (End Power On/Off Key)
Push once to end a call. Press for more than two
seconds to turn power on and off.
Hold
END
HOLD
PWR
CLEAR
Press to place a call on hold.
Press to control Keylock On/Off.
(Hold down the key more than 1.2~2 seconds)
DEF
1
ABC
3
CLEAR
2
Press to clear entry.
MNO
GHI
4
JKL
6
5
Press to control courtesy mode On/Off.
(Hold down the key more than 1.2~2 seconds)
Battery Compartment (in back)
PQ
WX
7RS
9 YZ
TUV
8
TRF/SHIFT
Press to transfer a call.
0
#
Press to switch between small and capital letter.
TRF
SHIFT
Programming Interface
(on Right Side)
Microphone
*
Mode 2 features are only available on NEAX 2000 IVS Series 1900
software or NEAX 2400 IMX Series 7300 software & Zone
Transceiver Version 5.00 software or later.
2
THE PSIII DISPLAY
or
18-digit, 4-line display
L1
L2
L1
L2
Battery indicates charge level. A solid battery
indicates a strong charge.
To view digit overflowing to the left and to the right.
To view line overflowing.
Illuminated V indicates that incoming call vibration
notification is active.
term
Off-hook, indicating the D
PSIII is off-hook.
Illuminated S indicates that incoming ring volume is
silent.
Signal strength, indicating strength or weakness of
signal being received. The antenna picture display
illuminates as the phone powers up, indicating that
the phone can make a call.
Illuminated
indicates that courtesy mode is on.
L1
*
Illuminated L1 indicates that originate a call.
Envelope indicates user has at least one voice mail
message or short text message.
L2
Illuminated L2 indicates that originate a call on the
second line.
Keylock status illuminates when Keylock is on.
*
Mode 2 features are only available on NEAX 2000 IVS Series 1900 software
or NEAX 2400 IMX Series 7300 software & Zone Transceiver Version 5.00
software or later.
Illuminated ANS indicates that Auto Answer is
active.
3
CHARGING THE BATTERY
Orange indicates charging is in progress,
light out indicates charging is complete.
L1
L2
HOLD
END
PWR
CLEAR
1
ABC
DEF
2
3
GHI
4
JKL
MNO
5
6
PQ
7RS
WX
9YZ
TUV
8
0
#
To recharge a handset (with the battery
pack inside) place phone here.
TRF
SHIFT
4
REPLACING THE BATTERY
1. To turn off power, press the END/PWR key and
hold more than tow seconds.
2. Remove a battery cover.
3. Pull out the connector, and then take out the battery.
4. Replace the battery.
5. Attach the battery cover.
5
TO
ORIGINATE A CALL
BASIC OPERATIONS
••••••••••••••••••••••••••••••••••••
NOTE: To originate a call, check that the battery
is charged and phone is turned on.
TO
TURN THE PHONE
ON
♦ Enter the telephone number.
Press the END/PWR key and hold for more than two
seconds. The PSIII displays the start-up greeting:
♦ Press the L1 or L2* key. PSIII displays:
Mode 1
Mode 2*
C.Cross
95551212
95551212
NOTE: If Calling Party Name is not available
then the calling party number will appear in the
display for Mode 2* systems.
indicates communication is available.
Or, for Offhook Dialing:
♦ Press the L1 or L2* key.
♦ Enter the telephone number. PSIII displays:
Mode 1
Mode 2*
C.Cross
95551212
95551212
L1
L1
*
Mode 2 features are only available on NEAX 2000 IVS Series 1900 software
or NEAX 2400 IMX Series 7300 software & Zone Transceiver Version 5.00
software or later.
6
TO
RECEIVE A CALL
TO
USE DIRECTORY DIALING
term
♦ As your D
PSIII rings the Line Indication will
Searching for Directory Entries Manually:
illuminate. PSIII displays:
♦ While in a standby state, press the Scroll S key.
Mode 1
Mode 2*
PSIII displays:
C.Cross
Directory
95551212
L1
95551212
L1
NOTE: If Calling Party Number is not available,
“CALL” is displayed. If Calling Party Name is
not available then the calling party number will
appear in the display (only for Mode 2* systems).
♦ To search the Directory in alphabetical order, press
the Scroll T key.
♦ You may press the Scroll S key to scan in reverse
♦ Press the L1 or L2* key (depending on what key is
order.
lit).
♦ When you found the name you are looking for,
♦ Begin speaking into the microphone.
press L1 or L2* to dial the number.
NOTE: If you cannot answer a call, “Missed
Call” is displayed.
*
Mode 2 features are only available on NEAX 2000 IVS Series 1900 software
or NEAX 2400 IMX Series 7300 software & Zone Transceiver Version 5.00
software or later.
7
Searching the Directory by Name:
TO
USE LAST NUMBER REDIAL
term
♦ While in a standby state, press the Scroll S key.
The D
called.
PSIII retains the last 20 numbers you have
PSIII displays:
♦ While the phone is in a standby state, press the
Scroll W key.
Directory
♦ The PSIII will display the last number dialed.
♦ If that is the number you wish to dial, press L1or
L2*
.
♦ Key in the first few letters of the Person’s last
name and then push the down key. The PSIII will
display names that start with those letters. If you
enter one character, the names that start with that
character will be displayed. When you enter two
characters, names that start with those characters,
will be displayed, and so on.
♦ If that is not the number you wish to dial, press the
Scroll T key to scroll through the last 20 numbers
dialed.
NOTE: If you dial the same number several
times, only the latest dialed information will be
displayed.
*
Mode 2 features are only available on NEAX 2000 IVS Series 1900 software
or NEAX 2400 IMX Series 7300 software & Zone Transceiver Version 5.00
software or later.
♦ If the name you’re looking for is not displayed,
use the Scroll T or Scroll S keys to locate the
next name and number. Continue to press the
Scroll T or Scroll S keys until you locate the
desired name.
T
O
USE SPEED DIAL
♦ While in a standby state, press the Scroll T key.
♦ Press L1 or L2* to dial the number.
PSIII displays:
v
♦ To make another selection, press the END/PWR
key, and then repeat above steps.
*
Mode 2 features are only available on NEAX 2000 IVS Series 1900 software
or NEAX 2400 IMX Series 7300 software & Zone Transceiver Version 5.00
software or later.
Speed Dial
(0-9)
8
To Search Speed Dial Number by Entering
Number:
CPN No.01
Jun/10 21:30
♦ Key in the speed dial number-0 through 9.
5482361201
♦ Press L1 or L2* to dial the number or press Scroll
key to scroll through the list of speed dial entries.
♦ The PSIII displays the number of the person who
To Search Speed Dial Number by Scroll Key:
called you most recently.
♦ Continue to press the Scroll T or Scroll S keys
♦ Press the Scroll T key repeatedly to scroll through
until you locate the desired Speed Dial Number.
the numbers of the last 20 people who called you.
♦ Press L1 or L2* to dial the Number.
♦ When you find the number you wish to call, press
L1or L2*
.
T
O
USE CALLING PARTY NUMBER
NOTE: If you wish to call someone who called you
from out of the office, enter access code (i.e. “9”) then
press FNC key and select CPN menu. At this time all
CPN numbers will have PBX access code included.
Calling Party Number (CPN) lets you scroll through
the last 20 numbers of people who called you. For
Mode 2* systems, it retains the last five calls received
on either L1 or L2*
If you access CPN before your phone receives its first
call, an error tone sounds and PSIII displays:
♦ In the standby state, your handset will display:
CPN Empty
J. KRAUSER
L1:12345
L2:90000
NOTE: If you receive the same number which has
already been stored, all number will be stored and
display the number of the person who called you lastly.
♦ Press the Scroll X key. PSIII displays:
*
Mode 2 features are only available on NEAX 2000 IVS Series 1900 software
or NEAX 2400 IMX Series 7300 software & Zone Transceiver Version 5.00
software or later.
9
NOTE: If Calling Party Name is not available
then the calling party number will appear in the
display.
T
O
TRANSFER A CALL
While you are speaking on the phone, the PSIII will
display:
♦ Press HOLD to place call on-hold.
Mode 1
Mode 2*
♦ Press L1 or L2* again to retrieve the call from
hold.
C.Cross
T
O
USE COURTESY MODE
95551212
95551212
Courtesy mode enables a PSIII incoming call to
become silent and vibration.
L1
L1
NOTE: If Calling Party Name is not available then the calling
party number will appear in the display for Mode 2* systems.
To Enable Courtesy Mode:
♦ If you wish to transfer this call, press TRF key.
♦ Press CLEAR key and hold it down for more than
two seconds. For Mode 2* systems, PSIII
displays:
♦ You will now hear a special dial tone. Key in the
telephone number you wish to transfer the call to.
♦ Press END/PWR to complete the transfer. Your
PSIII will return to the standby state.
J. KRAUSER
L1:12345
TO
PLACE A CALL
ON-HOLD
L2:90000
(Mode 2* System Only)
While you are speaking on the phone, the PSIII will
display:
To Disable Courtesy Mode:
♦ Press CLEAR key and hold it down for more than
two seconds.
NOTE: If DEFAULT SET or RESET ALL is invoked,
Courtesy Mode will be disabled.
C.Cross
95551212
L1
10
KEYPAD LOCK
NO SERVICE
Allows you to carry your phone without fear that
buttons may be inadvertently pushed, activating the
phone.
Your PSIII is out of the service area. The phone
cannot be used until it is within your wireless
coverage area. No Service indication may also
indicate that the number of visitors limit has been
exceeded when roaming.
To Lock Keypad:
♦ Press HOLD key and hold it down for more than
two seconds. For Mode 2* systems, PSIII
displays:
No Service
J. KRAUSER
L1:12345
NOTE: To turn phone off, press the END/PWR
L2:90000
key and hold for more than two seconds.
MISSED CALL
NOTE: After locking the keypad keys, you can
still receive incoming calls.
When your PSIII receive a call and a caller disconnect
the call, “Missed Call” will be displayed on the
standby screen.
To Unlock Keypad:
♦ Press HOLD key and hold it down for more than
two seconds.
Missed Call
C. Cross
*
Mode 2 features are only available on NEAX 2000 IVS Series 1900 software
or NEAX 2400 IMX Series 7300 software & Zone Transceiver Version 5.00
software or later.
95551212
NOTE: To disappered “Missed Call”, press the
END/PWR key.
11
PSIII FUNCTIONS
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
You may access the functions listed on the following
chart by pushing FNC key, and dialing digits.
12
FNC Menu
FNC
[3]
[2]
Off
Set
[1]
Phone Book
[2]
[3]
Soft Keys
[1]
Directory
[1]
[2]
Set
[1]
[2]
[3]
Add
Reset
Edit
Setup MSG
Delete
[1]
VM Number
[2]
Speed Dial
[1]
[1]
[2]
[3]
Add
[2]
MSG Storage
Edit
[1]
HNL
-HL
---
Delete
[2]
[2]
[3]
MSG Services
[3]
[1]
[2]
VM Access
TM Review
[3]
[4]
Protect TMM
[1]
On
Setup Menu
[1] PS Operation
[2]
Off
TM Reminder
[1]
[2]
[3]
[4]
[5]
[6]
[7]
Call Volume
[1]
[2]
On
[>]
(Up)
Off
[<]
(Down)
[4]
Ring Options
Vibration
[1]
[2]
[3]
[4]
Ring Volume
[1]
On
[>]
(Up)
[2]
Off
[<]
(Down)
Service ALM
Speaker Ring
[1]
On
[1]
On
[2]
Off
[2]
Off
CONF. Tone
STN Ring
[1]
On
[1]
L1
L2
[2]
Off
[2]
Key Click
[1]
Trunk Ring
On
[1]
[2]
L1
L2
[2]
Off
Key Light
[1]
[5]
CFW Program
On
[1]
CFW Busy
[2]
Off
[1]
Set
LED Flash
[1]
[2]
Reset
On
[2]
CFW D/A
13
FNC
[3]
[5]
[1]
Set
FNC
[3]
[7]
[1]
Set
[2]
Reset
[2]
Reset
[3]
[4]
[5]
CFW ALL
[5]
Protect DIR
[1]
[1]
Set
On
[2]
Reset
[2]
Off
CFW N/R
[6]
[7]
Default Set
[1]
[1]
Set
Set
Set
[2]
Reset
Reset All
[1]
Destination
[1]
[2]
Set
[4]
Soft Key
[1]
Reset
[6]
Display
[2]
[1]
Time Display
[3]
[1]
On
[4]
[2]
Off
[5]
[2]
[3]
Setup Time
[6]
[1]
Set
[7]
Name Entry
[8]
[1]
Set
[9]
[2]
Reset
[0]
[4]
Brightness
[>]
[5]
Forward Phone
(thick)
(thin)
[1]
[2]
[3]
[4]
CFW Busy
[<]
[1]
[2]
Set
[7]
Misc.
[1]
Reset
Headset Ring
CFW D/A
[1]
Auto
On
[1]
[2]
Set
[2]
Reset
[3]
Off
CFW ALL
[2]
[3]
[4]
Auto Answer
[1]
[2]
Set
[1]
L1
L2
Reset
[2]
CFW N/R
Answer Tone
[1]
[1]
[2]
Set
On
Reset
[2]
Off
[0]
Phone No.
Password
14
TO
ENTER NAMES IN THE DIRECTORY
Times
1
2
3
4
5
1
2
3
4
5
Key
Upper
Lower
♦ Press the FNC key →
1→1. PSIII displays:
1
.
A
D
G
J
,
B
E
H
K
N
Q
U
X
–
1
C
F
I
.
a
,
b
e
h
k
n
q
u
x
–
(
1
c
f
2
2
3
4
5
6
S
8
Z
2
3
4
5
6
s
3
d
Directory
[1]Add
[2]Edit
4
g
i
5
L
O
R
V
Y
0
j
l
[3]Delete
6
M
P
m
p
o
r
7
7
9
7
9
8
T
t
v
y
0
8
z
♦ Select [1] Add, then press the FNC key or 1. PSIII
displays:
9
W
SP
*
w
SP
*
0
*
#
(
#
)
#
)
Add Name?
SHIFT
Change to lower case
Change to upper case
* Character Chart
For example, press the “2” key once for “A,” twice
for “B,” three times for “C” and four times for the
number “2.” Press the SHIFT key to shift to lower
case mode.
♦ Key in the name using the following character
chart:
NOTE: Functions for Scroll W key – left Scroll at
display, “HOLD” – Pause inserted in dial
number and Scroll X key – Right Scroll at
display, are available but not displayed above
keys.
15
♦ When the name is complete, press the FNC key.
T
O
ENTER SPEED DIAL NUMBERS
PSIII displays:
♦ Press the FNC key→
1→2. PSIII displays:
Add Digits?
Speed Dial
[1]Add
[2]Edit
[3]Delete
♦ Key in the number. If pause is required, (e.g.; after
entering to gain access to an outside line) press
9
♦ Select [1] Add, then press the FNC key or 1. PSIII
“HOLD” to insert a pause.
♦ Press the FNC key to enter.
♦ Press FNC again to confirm.
displays:
[0]No Entry
[1]No Entry
[2]No Entry
[3]No Entry
♦ After the registration is completed, setting tone
will ring.
♦ After two seconds, return to the Directory Menu
page.
♦ Select “No Entry” Number.
NOTE: Do not remove the battery until at least
one minute has elapsed since entering Directory
or Speed Dial entries.
♦ Press the FNC key and register speed dial numbers
from [0] to [9]. PSIII displays:
Add Name?
♦ Key in the name using the character chart on the
previous page.
16
♦ Press the FNC key to enter name. PSIII displays:
TO
ACCESS VM (VOICE MAIL)
NOTE: This function depends on the external
Voice Mail Server.
Add Digits?
♦ When receiving VM. PSIII automatically displays:
(or pressing the FNC key →
2)
MSG Services
[1]VM Access
[2]TM Review
VMM
♦ Key in the digits for that number.
♦ Press the FNC key to enter digits.
♦ Press the FNC key again to confirm.
NOTE: When receiving VM and TM, PSIII
displays both “VMM” and “TMM”.
♦ After the registration is completed, setting tone
will ring.
♦ Select [1] VM Access, then press the FNC key or
♦ After two seconds, return to the Directory Menu
1. PS III displays:
page.
NOTE: Do not remove the battery until at least
one minute has elapsed since entering Directory
or Speed Dial entries.
VM Access
38000
♦ Press L1 or L2* to dial the number.
♦ Operate according to audio assist to receive VM.
*
Mode 2 features are only available on NEAX 2000 IVS Series 1900 software
or NEAX 2400 IMX Series 7300 software & Zone Transceiver Version 5.00
software or later.
17
TO
REVIEW TM (TEXT MESSAGE)
NOTE: This function depends on the OAI
application.
H#01 Jan/21 17:00
There is the gro
L#02 Jan/20 15:00
* Group meeting
♦ When receiving TM. PSIII automatically displays:
(or pressing the FNC key →
2)
♦ Press the Scroll T or Scroll S keys to locate the
desired message, the press the FNC key or wait for
two seconds to review. PSIII displays the detailed
message.
MSG Services
[1]VM Access
[2]TM Review
TMM
To return the TM list:
NOTE: When receiving VM and TM, PSIII
displays both “VMM” and “TMM”.
♦ Press the FNC key to return the TM list.
To Clear the TM:
♦ Select [2] TM Review, then press the FNC key or
2
. PSIII displays:
♦ To delete the message, press CLEAR. PSIII
NOTE: If Protect DIR is on, it is required to enter
your password.
displays:
H#01 Jan/21 17:00
There is the gro
[1]Delete
TM Review
New TM = 03
Total TM = 10
[2]List
♦ Select [1] Delete, then press the FNC key or
1.
♦ After two seconds, PSIII displays:
18
T
O
ADJUST CALL VOLUME
T
O
USE INCOMING CALL VIBRATION NOTIFI-
CATION
NOTE: Incoming call vibration notification is not
While you are speaking on the phone, the PSIII will
display:
active when either L1 or L2* is busy.
To Enable Incoming Call Vibration Notifica-
tion:
C.Cross
♦ Press the FNC key →
3→1→2. PSIII displays:
95551212
L1
♦ Press the Scroll W or Scroll X key to adjust Call
Vibration
[1]On
Volume, the PSIII will display:
[2]Off
Call Volume
♦ Select [1] On, then press the FNC key or
1.
Maximum
L1
♦ After two seconds, the incoming call vibration
notification (“V”) will appear on the LCD.
♦ Press the Scroll W key to lower or Scroll X key to
increase Call Volume.
*
Mode 2 features are only available on NEAX 2000 IVS Series 1900 software
or NEAX 2400 IMX Series 7300 software & Zone Transceiver Version 5.00
software or later.
NOTE: In the stand by state, press the FNC key→
3→1→1.
Operation and the display are the same to those above.
19
♦ After two seconds, return to the standby state.
To Disable Incoming Call Vibration Notifica-
tion:
To Turn Off Service Alarm:
♦ Press the FNC key →3→1→2. PSIII displays:
♦ Press the FNC key →
3→1→3. PSIII displays:
Vibration
[1]On
[2]Off
Service ALM
[1]On
[2]Off
♦ Select [2] Off, then press the FNC key or
2.
♦ Select [2] Off, then press the FNC key or to turn
1
off Service Alarm for Mode 2* systems.
SERVICE ALARM
♦ Setting tone will ring.
Enables you to know when you are in an area without
service, or if the battery is running low.
♦ After two seconds, return to the standby state.
*
Mode 2 features are only available on NEAX 2000 IVS Series 1900 software
or NEAX 2400 IMX Series 7300 software & Zone Transceiver Version 5.00
software or later.
To Turn On Service Alarm:
♦ Press the FNC key →3→1→3. PSIII displays:
Service ALM
[1]On
[2]Off
♦ Select [1] On, then press the FNC key or to turn
1
on Service Alarm for Mode 2* systems.
♦ Setting tone will ring.
20
♦ Select [2] Off, then press the FNC key or to turn
1
CONFIRMATION TONE
off Confirmation Tone for Mode 2* systems.
Enables you to hear a tone that lets you know that you
made an error or for confirming that you entered
information properly.
♦ Setting tone will ring.
♦ After two seconds, return to the standby state.
To Turn On Confirmation Tone:
*
Mode 2 features are only available on NEAX 2000 IVS Series 1900 software
or NEAX 2400 IMX Series 7300 software & Zone Transceiver Version 5.00
software or later.
♦ Press the FNC key →3→1→4. PSIII displays:
CONF. Tone
[1]On
[2]Off
♦ Select [1] On, then press the FNC key or to turn
1
on Confirmation Tone for Mode 2* systems.
♦ Setting tone will ring.
♦ After two seconds, return to the standby state.
To Turn Off Confirmation Tone:
♦ Press the FNC key →3→1→4. PSIII displays:
CONF. Tone
[1]On
[2]Off
21
♦ After two seconds, return to the standby state.
KEY CLICK
*
Mode 2 features are only available on NEAX 2000 IVS Series 1900 software
or NEAX 2400 IMX Series 7300 software & Zone Transceiver Version 5.00
software or later.
Enables you to hear a beep as you press each key.
To Turn On Key Click:
♦ Press the FNC key →
3→1→5. PSIII displays:
Key Click
[1]On
[2]Off
♦ Select [1] On, then press the FNC key or to turn
1
on key click for Mode 2* systems.
♦ Setting tone will ring.
♦ After two seconds, return to the standby state.
To Turn Off Key Click:
♦ Press the FNC key →
3→1→5. PSIII displays:
Key Click
[1]On
[2]Off
♦ Select [2] Off, then press the FNC key or to turn
2
off key click for Mode 2* systems.
♦ Setting tone will ring.
22
♦ After two seconds, return to the standby state.
KEY LIGHT
Controls the backlight of the keys.
LED FLASH
Controls LED Ring Indicator. Red Light indicates
incoming call.
To Turn Key light On:
♦ Press the FNC key →3→1→6. PSIII displays:
To Turn On LED Flash:
♦ Press the FNC key →
3→1→7. PSIII displays:
Key Light
[1]On
[2]Off
LED Flash
[1]On
[2]Off
♦ Select [1] On, then press the FNC key or to turn
1
Key Light on for Mode 2* systems.
♦ Select [1] On, then press the FNC key or to turn
1
♦ Setting tone will ring.
LED Flash on for Mode 2* systems.
♦ After two seconds, return to the standby state.
♦ Setting tone will ring.
♦ After two seconds, return to the standby state.
To Turn Key Light Off:
♦ Press the FNC key →3→1→6. PSIII displays:
To Turn Off LED Flash:
♦ Press the FNC key →
3→1→7. PSIII displays:
Key Light
[1]On
[2]Off
LED Flash
[1]On
[2]Off
♦ Select [2] Off, then press the FNC key or to turn
2
Key Light off for Mode 2* systems.
*
Mode 2 features are only available on NEAX 2000 IVS Series 1900 software
or NEAX 2400 IMX Series 7300 software & Zone Transceiver Version 5.00
software or later.
♦ Setting tone will ring.
23
♦ Select [2] Off, then press the FNC key or to turn
2
LED Flash off for Mode 2* systems.
♦ Setting tone will ring.
Display?
PICK
♦ After two seconds, return to the standby state.
PROGRAM SOFTKEYS
♦ Enter up to 5 characters or numbers that you wish
to display for this softkey.
Confirm your administrator for a list of access codes
which can be used to program softkeys.
♦ Press the FNC key to enter. PSIII displays:
To Set Softkey:
Hook Flash?
[1]Yes
♦ Press the FNC key →
3→2. PSIII displays:
[2]No
Soft Key
[1]Set
[2]Reset
♦ If you need to precede the access code or
extension with a hook-flash then select [1] Yes.
Otherwise select [2] No. PSIII displays:
♦ Press the FNC key or 1. PSIII displays:
Digits?
Display?
♦ Enter up to 40 numbers to dial or access codes to
initiate.
♦ Key in the name using the character chart on the
♦ Press the FNC key to enter.
previous page. PSIII displays:
♦ Press the FNC key again to confirm.
24
♦ Setting tone will ring.
♦ After two seconds, return to the standby state.
PICK
To Reset Softkeys:
H100
♦ Press the FNC key
3→2, then select [2] Reset.
PSIII displays:
♦ Press the FNC key to confirm or END/PWR to
cancel.
Soft Key
[1]Set
♦ Setting tone will ring.
[2]Reset
♦ After two seconds, return to the standby state.
TO
SET VM (VOICE MAIL) NUMBER
♦ Press the FNC key or 2. PSIII displays:
NOTE: This function depends on the external
Voice Mail Server.
♦ Press the FNC key →
3→3→1. PSIII displays:
Soft Key
[1]PICK
[2]PARK
[3]CAMP
VM Number
[1]Set
♦ Use the Scroll T or Scroll S keys to search the
number and name of the softkey to erase.
♦ Select the softkey to erase, then press the FNC key
or the number to confirm. PSIII displays:
(flashing)
♦ Select [1] Set.
Access No?
25
♦ Key in the number.
♦ Select [1] HNL, [2] -NL or [3] - - -, then press the
FNC key or the number.
♦ Press the FNC key to enter.
♦ Press the FNC key to confirm.
♦ Setting tone will ring.
♦ A maximum of 10 messages are kept in the PSIII
handset. When it is full, PSIII displays:
♦ After two seconds, return to the standby state.
NOTE: Confirm your system administrator for
the list of VM access code.
TM Full
MESSAGE STORAGE
This function enable PSIII to set whether overwrite or
save the TM when a TM arrived at a mail box of the
Server (external equipment).
PROTECT TMM (TEXT MAIL MESSAGE)
NOTE: This function depends on the OAI
application.
NOTE: This function depends on the OAI
application.
NOTE: TM transmission route is only one way:
STM server→ PSIII.
Restricts to browse TMM.
To Turn On Protect TMM:
♦ Press the FNC key →
3→3→2. PSIII displays:
♦ Press the FNC key →
3→3→3. PSIII displays:
MSG Storage
[1]HNL
[2]-NL
Protect TMM
[1]On
[2]Off
[3]---
[1] HNL: H (High), N (Normal), L (Low) will be
overwritten.
♦ Select [1] On, then press the FNC key or 1. PSIII
[2] -NL: N, L will be overwritten.
displays:
[3] - - -: Do not overwrite.
26
Password?
Password?
♦ Key in current password.
♦ Key in current password.
♦ Press the FNC key to enter. PSIII displays:
♦ Press the FNC key to enter. PSIII displays:
Protect TMM
Set
Protect TMM
Reset
♦ Setting tone will ring.
♦ Setting tone will ring.
♦ After two seconds, return to the standby state.
♦ After two seconds, return to the standby state.
To Turn Off Protect TMM:
TM REMINDER
♦ Press the FNC key →
3→3→3. PSIII displays:
NOTE: This function depends on the OAI
application.
When unread TM exists, warning will be sent every
time you return to the standby state. PSIII displays:
Protect TMM
[1]On
[2]Off
Received new TM
♦ Select [2] Off, then press the FNC key or 2. PSIII
displays:
27
To Turn On TM Reminder:
♦ Press the FNC key →
3→3→
4. PSIII displays:
TM Reminder
Off
TM Reminder
[1]On
[2]Off
♦ Setting tone will ring.
♦ After two seconds, return to the standby state.
♦ Select [1] On, then press the FNC key or 1. PSIII
TO
ADJUST RING VOLUME
displays:
Default setting is “Standard”.
TM Reminder
On
NOTE: For Mode 2* systems, the ring volume
controls both L1 or L2*
.
♦ Press the FNC key →
3→4. PSIII displays:
♦ Setting tone will ring.
Ring Options
[1]Ring Volume
[2]Speaker Ring
[3]STN Ring
♦ After two seconds, return to the standby state.
To Turn Off TM Reminder:
♦ Press the FNC key →
3→3→4. PSIII displays:
♦ Select [1] Ring Volume, then press the FNC key or
. PSIII displays:
1
TM Reminder
[1]On
[2]Off
Ring Volume
Standard
♦ Select [2] Off, then press the FNC key or 2. PSIII
displays:
28
To Turn Off Ring:
To Turn Down Ring Volume:
♦ Press the Scroll W key two times. PSIII displays:
♦ Press the Scroll W key. PSIII displays:
Ring Volume
Silent
Ring Volume
Low
♦ Press the FNC key or leave five seconds. PSIII
*
Mode 2 features are only available on NEAX 2000 IVS Series 1900 software
or NEAX 2400 IMX Series 7300 software & Zone Transceiver Version 5.00
software or later.
displays:
SPEAKER RING
J. KRAUSER
L1:12345
(Mode 2* System Only)
L2:90000
Allows you to disable incoming calls from ringing
while on a call.
To Turn Up Ring Volume:
To Disable Speaker Ring:
♦ Press the Scroll X key. PSIII displays:
♦ Press the FNC key →
3→4. PSIII displays:
Ring Options
[1]Ring Volume
[2]Speaker Ring
[3]STN Ring
Ring Volume
Maximum
29
♦ Select [2] Speaker Ring. PSIII displays:
STN Ring
[1]L1
[2]L2
Speaker Ring
[1]On
[2]Off
♦ Select L1 or L2* by using the Scroll T or Scroll
S
keys. For Mode 2* systems, PSIII displays:
♦ Select [2] Off, then press the FNC key or to
2
disable speaker ring.
STN Ring
1 2 3 4 5 6 7 8
Speaker Ring
Off
♦ Press the Scroll W or Scroll X keys or the number
key to select a different Station Ring Pattern.
♦ Setting tone will ring.
♦ Press the FNC key to confirm.
♦ Setting tone will ring.
♦ After two seconds, return to the standby state.
♦ After two seconds, return to the standby state.
NOTE: The default Station Ring pattern is 1.
STATION RING
Allows you to assign ring patterns that tell users
whether an incoming call is from an internal or
external source.
TRUNK RING
Allows you to assign ring patterns that tell users
whether an incoming call is from an internal or
external source.
To Change the Station Ring Pattern:
♦ Press the FNC key →
3→4→3. PSIII displays:
To Change the Trunk Ring Pattern:
♦ Press the FNC key →
3→4→4. PSIII displays:
30
To Set the Call Forwarding Busy Access Code:
Trunk Ring
[1]L1
♦ Press the FNC key →3→5→1. PSIII displays:
[2]L2
CFW Busy
[1]Set
[2]Reset
♦ Select L1 or L2* by using the Scroll S or Scroll
T
key. For Mode 2* systems, PSIII displays:
♦ Press the FNC key or 1. For Mode 2* systems,
PSIII displays:
Trunk Ring
1 2 3 4 5 6 7 8
Access No?
♦ Press the Scroll W or Scroll X or the number key to
select different Trunk Ring pattern.
♦ Key in the access code to establish call forwarding
♦ Press the FNC key to confirm.
when busy.
♦ Setting tone will ring.
Example: *3=Call Forward Busy, SET.
♦ After two seconds, return to the standby state.
NOTE: The default Trunk Ring pattern is 2.
♦ Press the FNC key to enter.
♦ Press the FNC key to confirm.
♦ Setting tone will ring.
T
O
SET CALL FORWARDING
♦ After two seconds, return to the standby state.
[Call Forwarding Busy]
*
Mode 2 features are only available on NEAX 2000 IVS Series 1900 software
or NEAX 2400 IMX Series 7300 software & Zone Transceiver Version 5.00
software or later.
Enables you to set the access code which is used to
establish call forwarding when your line is busy.
NOTE: Check with your system administrator for
the list of access codes.
31
To Set the Call Forwarding Busy Cancel
Access Code:
[Call Forwarding Don’t Answer]
Enables you to set the access code which is used to
establish Call Forwarding when you do not answer
the phone.
♦ Press the FNC key →3→5→1. PSIII displays:
NOTE: Confirm your system administrator for
the list of access codes.
CFW Busy
[1]Set
[2]Reset
To Set the Call Forwarding Don’t Answer
Access Code:
♦ Press the FNC key →
3→5→2. PSIII displays:
♦ Press the FNC key or 2. For Mode 2* systems,
PSIII displays:
CFW D/A
[1]Set
[2]Reset
Access No?
♦ Press the FNC key or 1. For Mode 2* systems,
PSIII displays:
♦ Key in the access code to cancel call forwarding.
Example: #3=Call Forward Busy, Cancel.
♦ Press the FNC key to enter.
Access No?
♦ Press the FNC key to confirm.
♦ Setting tone will ring.
*
Mode 2 features are only available on NEAX 2000 IVS Series 1900 software
or NEAX 2400 IMX Series 7300 software & Zone Transceiver Version 5.00
software or later.
♦ After two seconds, return to the standby state.
32
♦ Key in the access code to establish call forwarding
Example: #4=Call Forward Don’t Answer Cancel.
when call is not answered.
♦ Press the FNC key to enter.
Example: *4=Call Forward Don’t Answer, SET.
♦ Press the FNC key to confirm.
♦ Setting tone will ring.
♦ Press the FNC key to enter.
♦ Press the FNC key to confirm.
♦ Setting tone will ring.
♦ After two seconds, return to the standby state.
[Call Forwarding All Calls]
♦ After two seconds, return to the standby state.
To set the access code to establish Call Forwarding
All Calls.
To Set the Call Forwarding Don’t Answer Can-
cel Access Code:
NOTE: Confirm your system administrator the
list of access codes.
♦ Press the FNC key →3→5→2. PSIII displays:
To Set the Call Forwarding All Calls Access
Code:
CFW D/A
[1]Set
[2]Reset
♦ Press the FNC key →
3→5→3. PSIII displays:
CFW ALL
[1]Set
[2]Reset
♦ Press the FNC key or 2. For Mode 2* systems,
PSIII displays:
♦ Press the FNC key or 1. For Mode 2* systems,
Access No?
PSIII displays:
*
Mode 2 features are only available on NEAX 2000 IVS Series 1900 software
or NEAX 2400 IMX Series 7300 software & Zone Transceiver Version 5.00
software or later.
♦ Key in the access code to cancel Call Forwarding
Don’t Answer.
33
Access No?
Access No?
♦ Key in the access code to establish Call
♦ Key in the access code to cancel Call Forwarding
Forwarding All Calls.
All Calls.
Example: *2=Call Forward-All, SET
Example: #2=Call Forward-All Cancel.
♦ Press the FNC key to enter.
♦ Press the FNC key to enter.
♦ Press the FNC key to confirm.
♦ Setting tone will ring.
♦ Press the FNC key to confirm.
♦ Setting tone will ring.
♦ After two seconds, return to the standby state.
♦ After two seconds, return to the standby state.
*
Mode 2 features are only available on NEAX 2000 IVS Series 1900 software
or NEAX 2400 IMX Series 7300 software & Zone Transceiver Version 5.00
software or later.
To Set the Call Forwarding All Calls Cancel
Access Code:
♦ Press the FNC key →3→5→3. PSIII displays:
CFW ALL
[1]Set
[2]Reset
♦ Press the FNC key or 2. For Mode 2* systems,
PSIII displays:
34
♦ Press the FNC key to enter.
[Call Forwarding No Response]
To set the access code to establish call forwarding
when the handset is not within the wireless system
service area or is turned off.
♦ Press the FNC key to confirm.
♦ Setting tone will ring.
♦ After two seconds, return to the standby state.
NOTE: Confirm your system administrator for
the list of access codes.
To Set the Call Forwarding No Response Can-
cel Access Code:
To Set the Call Forwarding No Response
Access Code:
♦ Press the FNC key →
3→5→4. PSIII displays:
♦ Press the FNC key →3→5→4. PSIII displays:
CFW N/R
[1]Set
[2]Reset
CFW N/R
[1]Set
[2]Reset
♦ Press the FNC key or 2. For Mode 2* systems,
PSIII displays:
♦ Press the FNC key or 1. For Mode 2* systems,
PSIII displays:
Access No?
Access No?
♦ Key in the access code to cancel Call Forwarding.
♦ Key in the access code to establish Call
Forwarding when No Response.
Example: #9=Call Forward-NR, Cancel.
Example: *9=Call Forward-NR, SET.
*
Mode 2 features are only available on NEAX 2000 IVS Series 1900 software
or NEAX 2400 IMX Series 7300 software & Zone Transceiver Version 5.00
software or later.
35
♦ Press the FNC key to enter.
♦ Press the FNC key to enter name. PSIII displays:
♦ Press the FNC key to confirm.
♦ Setting tone will ring.
Digits?
♦ After two seconds, return to the standby state.
TO
SET CALL FORWARDING DESTINATION
♦ Key in the digits for that number.
♦ Press the FNC key to enter digits.
♦ Press the FNC key again to confirm.
Forwarding destination number and name must be
previously assigned.
To Set Call Forwarding Destination:
♦ Press the FNC key →
3→5→5. PSIII displays:
♦ After the registration is completed, setting tone
will ring.
♦ After two seconds, return to the standby state.
Destination
[1]Set
[2]Reset
To Reset Call Forwarding Destination:
♦ Press the FNC key →
3→5→5. PSIII displays:
♦ Select [1] Set, then press the FNC key or 1. PSIII
Destination
[1]Set
displays:
[2]Reset
Display?
♦ Select [2] Reset, then press the FNC key or
2.
PSIII displays:
♦ Key in the destination name using the character
chart on the previous page.
36
TIME DISPLAY
Destination
[1]Group
To Enable Time Display:
[2]Desk
[3]Voice Mail
♦ Press the FNC key →
3→6→1. PSIII displays:
Time Display
[1]On
[2]Off
♦ Select the destination to erase, then press the FNC
key.
♦ Confirm the displayed destination to erase
(flashing), then press the FNC key. PSIII displays:
♦ Select [1] On, then press the FNC key or 1. PSIII
displays:
Destination
Reset
Time Display
On
♦ Setting tone will ring.
♦ After two seconds, return to the standby state.
♦ Setting tone will ring.
♦ After two seconds, return to the standby state.
To Disable Time Display:
♦ Press the FNC key →
3→6→1. PSIII displays:
Time Display
[1]On
[2]Off
37
♦ Select [2] Off, then press the FNC key or
2. PSIII
♦ Press the FNC key →3→6→2. PSIII displays:
displays:
Setup Time
Set
Time Display
Off
♦ Setting tone will ring.
♦ After two seconds, return to the standby state.
♦ Setting tone will ring.
♦ After two seconds, return to the standby state.
TO
ENTRY NAME
TO
SETUP TIME
Name will be displayed in the standby state.
Default setting is “My HANDSET”.
To Entry Name:
♦ Press the FNC key →
3→6→2. PSIII displays:
Setup Time
[1]Set
♦ Press the FNC key →
3→6→3. PSIII displays:
Name Entry
[1]Set
[2]Reset
♦ Select [1] Set, then press the FNC key or 1. PSIII
displays:
♦ Select [1] Set, then press the FNC key or 1. PSIII
00/00/2000
00:00
displays:
♦ Press the Scroll W or Scroll X keys, and key in
Month/Day/Year and Hour/Minute.
38
Name?
My HANDSET
My HANDSET
♦ Press CLEAR key to delete the displayed
♦ Default setting is displayed.
♦ Press the FNC key to enter.
characters, then key in name.
♦ Press the FNC key to enter.
♦ Setting tone will ring.
♦ Press the FNC key to confirm.
♦ Setting tone will ring.
♦ After two seconds, return to the standby state.
♦ After two seconds, return to the standby state.
To Reset Name:
♦ Press the FNC key →
3→6→3. PSIII displays:
Name Entry
[1]Set
[2]Reset
♦ Select [2] Reset, then press the FNC key or
2.
PSIII displays:
39
TO
ADJUST BRIGHTNESS
Headset Ring
On
To Set Brightness of Display:
♦ Press the FNC key →3→6→4. PSIII displays:
♦ Setting tone will ring.
Brightness
♦ After two seconds, return to the standby state.
1 2 3 4 5 6 7 8 9
To Turn On Automatic Headset Ring:
Automatic headset ring causes your phone to ring
automatically in the headset whenever a headset is
plugged in.
♦ Press the Scroll W to light or Scroll X key to dark
Brightness.
♦ Press the FNC key →
3→7→1. PSIII displays:
HEADSET RING
When using a headset, allows your phone to ring
through to your headset.
Headset Ring
[1]Auto
[2]On
To Turn On Headset Ring:
[3]Off
♦ Press the FNC key →
3→7→1. PSIII displays:
♦ Select [1] Auto for Mode 2* systems.
Headset Ring
[1]Auto
[2]On
♦ Press the FNC key or to turn on Automatic
1
Headset Ring.
[3]Off
♦ Setting tone will ring.
♦ After two seconds, return to the standby state.
♦ Select [2] On, then press the FNC key or to turn
2
*
Mode 2 features are only available on NEAX 2000 IVS Series 1900 software
or NEAX 2400 IMX Series 7300 software & Zone Transceiver Version 5.00
software or later.
on Headset Ring. For Mode 2* systems, PSIII
displays:
40
To Turn Off Headset Ring:
♦ Press the FNC key →
3→7→1. PSIII displays:
Auto Answer
[1]L1
[2]L2
Headset Ring
[1]Auto
[2]On
[3]Off
♦ Select L1 or L2 by using the Scroll Sor Scroll
T
keys. For Mode 2* systems, PSIII displays:
♦ Select [3] Off for Mode 2* system.
Auto Answer
[1]On
♦ Press the FNC key or to turn off Headset Ring.
3
[2]Off
♦ Setting tone will ring.
♦ After two seconds, return to the standby state.
*
Mode 2 features are only available on NEAX 2000 IVS Series 1900 software
or NEAX 2400 IMX Series 7300 software & Zone Transceiver Version 5.00
software or later.
♦ Select [1] On, then press the FNC key or 1. PSIII
displays:
AUTOMATIC ANSWER
Answer Time
(00-20)
Enables you to receive calls without first having to
press the L1 or L2* button.
5
NOTE: Automatic Answer is not active when
either L1 or L2* is busy.
♦ Dial the number of seconds you want the phone to
ring before the call is automatically answered from
0 to 20.
To Turn On Automatic Answer:
♦ Press the FNC key →
3→7→2. PSIII displays:
♦ Press the FNC key to enter.
♦ Setting tone will ring.
41
♦ After two seconds, return to the standby state.
PSIII displays:
Auto Answer
Reset?
J. KRAUSER
L1:12345
L2:90000
♦ Press the FNC key to enter. PSIII displays:
♦ Key entry will not use.
Auto Answer
Reset
To Turn Off Automatic Answer:
♦ Press the FNC key →
3→7→2. PSIII displays:
♦ Setting tone will ring.
Auto Answer
[1]L1
[2]L2
♦ After two seconds, return to the standby state.
*
Mode 2 features are only available on NEAX 2000 IVS Series 1900 software
or NEAX 2400 IMX Series 7300 software & Zone Transceiver Version 5.00
software or later.
♦ Select L1 or L2 by using the Scroll S or Scroll
ANSWER TONE
Tkeys. For Mode 2* systems, PSIII displays:
Enables you to hear a warning tone for an incoming
call before Auto Answer.
Auto Answer
[1]On
[2]Off
♦ Select [2] Off, then press the FNC key or 2. PSIII
displays:
42
To Turn On Answer Tone:
PASSWORD
♦ Press the FNC key →
3→
7→3. PSIII displays:
Enables you to set a password. Passwords are 4
characters long. The default password is 0000.
Answer Tone
[1]On
[2]Off
To Set Password:
♦ Press the FNC key →
3→7→4. PSIII displays:
Password
[1]Set
[2]Reset
♦ Select [1] On, then press the FNC key or to turn
1
on Answer Tone for Mode 2* systems.
♦ Setting tone will ring.
♦ After two seconds, return to the standby state.
♦ Press the FNC key or 1. For Mode 2* systems,
PSIII displays:
To Turn Off Answer Tone:
♦ Press the FNC key →3→7→3. PSIII displays:
Old Password?
Answer Tone
[1]On
[2]Off
♦ Key in old password.
*
Mode 2 features are only available on NEAX 2000 IVS Series 1900 software
or NEAX 2400 IMX Series 7300 software & Zone Transceiver Version 5.00
software or later.
♦ Select [2] Off, then press the FNC key or to turn
2
off Answer Tone for Mode 2* systems.
♦ Setting tone will ring.
♦ After two seconds, return to the standby state.
43
♦ Press the FNC key to confirm old password. PSIII
displays:
Password
[1]Set
[2]Reset
New Password?
♦ Press the FNC key or 2. For Mode 2* systems,
PSIII displays:
♦ Key in password.
♦ Press the FNC key to enter the password.
♦ Key in password twice.
Password?
♦ Press the FNC key to confirm. PSIII displays:
♦ Key in current password.
♦ Press the FNC key to confirm. PSIII displays:
New Password
Set
Password
Reset
♦ Setting tone will ring.
♦ After two seconds, return to the standby state.
♦ Setting tone will ring.
To Cancel the Password:
♦ After two seconds, return to the standby state.
♦ Press the FNC key →3→7→4. PSIII displays:
NOTE: The Password has now been reset to:
0000.
*
Mode 2 features are only available on NEAX 2000 IVS Series 1900 software
or NEAX 2400 IMX Series 7300 software & Zone Transceiver Version 5.00
software or later.
44
PROTECT DIRECTORY
Enables you to protect the directory to ensure the
privacy of stored telephone numbers.
Protect DIR
Set
NOTE: This will also prevent all access to the
directory, (i.e. view, add, edit or delete).
WARNING: Using Reset All will delete all
numbers in the directory even if Protect Directory
is on.
♦ Setting tone will ring.
♦ After two seconds, return to the standby state.
To Turn On Protect Directory:
To Turn Off Protect Directory:
♦ Press the FNC key →
3→7→5. PSIII displays:
♦ Press the FNC key →
3→7→5. PSIII displays:
Protect DIR
[1]On
[2]Off
Protect DIR
[1]On
[2]Off
♦ Press the FNC key or to turn on Protect
1
♦ Press the FNC key or to turn off Protect
2
Directory. For Mode 2* systems, PSIII displays:
Directory. For Mode 2* systems, PSIII displays:
Password?
Password?
♦ Key in password.
*
Mode 2 features are only available on NEAX 2000 IVS Series 1900 software
or NEAX 2400 IMX Series 7300 software & Zone Transceiver Version 5.00
software or later.
♦ Press the FNC key to confirm. PSIII displays:
45
♦ Key in password.
Functions
Default Setting
♦ Press the FNC key to confirm. PSIII displays:
Trunk Ring
Pattern 2
On
Time Display
Headset Ring
Auto Answer
Answer Tone
Password
Auto
Off
Protect DIR
Reset
On
Off, Password is 0000
Protect DIR
Courtesy Mode
Off
Off
♦ Setting tone will ring.
♦ After two seconds, return to the standby state.
To Invoke Default Set:
♦ Press the FNC key →
3→7→6. PSIII displays:
DEFAULT SET
Allows you to reset your handset to all the factory-set
defaults:
Default Set
[1]Set
Functions
Default Setting
Call Volume
Standard
Off
Vibration
Service ALM
CONF. Tone
Key Click
On
♦ Press the FNC key or 1. For Mode 2* systems,
On
PSIII displays:
On
Key Light
On
LED Flash
On
Execute?
MSG Storage
Protect TMM
TM Reminder
Ring Volume
Speaker Ring
STN Ring
– – –
Off
Off
Standard
On
*
Mode 2 features are only available on NEAX 2000 IVS Series 1900 software
or NEAX 2400 IMX Series 7300 software & Zone Transceiver Version 5.00
software or later.
Pattern 1
46
♦ Press the FNC key to confirm. For Mode 2*
Functions
Default Setting
systems, PSIII displays:
Ring Volume
Standard
On
Speaker Ring
STN Ring
Pattern 1
Pattern 2
Trunk Ring
CFW Busy
CFW D/A
Default Set
Complete
Delete all registered data
Delete all registered data
Delete all registered data
Delete all registered data
Delete all registered data
On
CFW All
CFW N/R
♦ Setting tone will ring.
Destination
Time Display
Name Entry
Headset Ring
Auto Answer
Answer Tone
Password
♦ After two seconds, return to the standby state.
Delete all registered data
Auto
RESET ALL
Setting: Off, Registered time: Brank
On
Primarily a maintenance function. Resets all settings
to what they were when the handset left the factory.
Settig: Off, Password: 0000
Off
Functions
Default Setting
Protect DIR
Phone Book
Call Volume
Standard
Off
Delete all registered data for Direc-
tory, Speed Dial
Vibration
Service ALM
CONF. Tone
Key Click
On
TM Review
Courtesy mode
LNR
Delete revieved TM message
On
Off
On
Deleted
Deleted
Key Light
On
CPN
LED Flash
Soft Key
On
Delete all registered data
VM Number
MSG Storage
Protect TMM
TM Reminder
Delete all registered data
- - -
Off
Off
47
To Invoke Reset All:
♦ Press the FNC key →
3→7→7. PSIII displays:
Execute?
Reset All
[1]Set
♦ Press the FNC key to confirm. PSIII displays:
♦ Press the FNC key or 1. For Mode 2* systems,
PSIII displays:
Reset All
Complete
Password?
♦ Setting tone will ring.
♦ After two seconds, return to the standby state.
*
Mode 2 features are only available on NEAX 2000 IVS Series 1900 software
or NEAX 2400 IMX Series 7300 software & Zone Transceiver Version 5.00
software or later.
♦ Key in password.
♦ Press the FNC key to confirm. PSIII displays:
ACCESS SOFTKEYS
Followings are an example when softkey codes have
been programmed.
Reset All?
♦ Press the FNC key →4. PSIII displays:
♦ Press the FNC key to confirm. PSIII displays:
48
Soft Key
[1]PICK
[2]PARK
[3]CAMP
Forward Phone
[1]CFW Busy
[2]CFW D/A
[3]CFW All
♦ Select the desired softkey by using the Scroll T or
♦ Select [5] ForwardPhone.
Scroll S keys.
To Forward Busy Calls:
♦ Press the FNC key or the number to confirm. PSIII
displays:
♦ Select [1] CFW Busy. PSIII displays:
CFW Busy
[1]Set
PICK
[2]Reset
100
♦ Press L1 or L2* to dial the number.
♦ Select [1] Set, and press the FNC key or
1.
♦ By pressing L1 or L2*, PSIII displays:
TO
USE CALL FORWARDING
NOTE: Before using this feature, the call
forwarding access codes need to be established.
Refer to PSIII Functions to set call forwarding
access codes.
CFW Busy
[1]Voice Mail
[2]Group
[3]Desk
Call Forwarding allows you to forward incoming calls
to other numbers.
L1
♦ Select the line to forward from preassigned
destination number (NOTE).
♦ While the phone is in a standby state, press the
FNC key →5. PSIII displays:
♦ To input the number directly, select last menu
“Input number”.
For example, PSIII displays:
49
To Forward Not Answered Calls:
♦ Select [2] CFW D/A. PSIII displays:
CFW Busy
[2]Group
[3]Desk
[4]Input Number
L1
CFW D/A
[1]Set
[2]Reset
*
Mode 2 features are only available on NEAX 2000 IVS Series 1900 software
or NEAX 2400 IMX Series 7300 software & Zone Transceiver Version 5.00
software or later.
Note: Destination number can be assigned in TO SET CALL FORWARDING
DESTINATION FNC key →
(
3→5→5)
♦ Select [1] Set, then press the FNC key or
1.
♦ For the call forwarding destination, refer to the
procedure in To Forward Busy Calls.
To Forward All Calls:
♦ Select [3] CFW All. PSIII displays:
CFW All
[1]Set
[2]Reset
♦ Select [1] Set, then press the FNC key or
1.
♦ For the call forwarding destination, refer to the
procedure in To Forward Busy Calls.
50
To Forward No Response Calls:
This forward is enabled when the handset is either
turned off or has left the service area.
J. KRAUSER
L1:12345
L2:90000
♦ Select [4] CFW N/R. PSIII displays:
CFW N/R
[1]Set
[2]Reset
♦ Select [1] Set, then press the FNC key or
1.
♦ For the call forwarding destination, refer to the
procedure in To Forward Busy Calls.
PHONE
NO.
Enables to display your Phone Number while time
display is On.
♦ Press the FNC key in the standby state. PSIII
displays:
[3]Setup Menu
[4]Soft Key
[5]ForwardPhone
[0]Phone No.
♦ Select [0] Phone No., then press the FNC key or
0.
PSIII displays your number:
51
NOTES
___________________________________________________________________________________________
___________________________________________________________________________________________
___________________________________________________________________________________________
___________________________________________________________________________________________
___________________________________________________________________________________________
___________________________________________________________________________________________
___________________________________________________________________________________________
___________________________________________________________________________________________
___________________________________________________________________________________________
___________________________________________________________________________________________
___________________________________________________________________________________________
___________________________________________________________________________________________
___________________________________________________________________________________________
___________________________________________________________________________________________
___________________________________________________________________________________________
___________________________________________________________________________________________
___________________________________________________________________________________________
___________________________________________________________________________________________
___________________________________________________________________________________________
___________________________________________________________________________________________
___________________________________________________________________________________________
52
|
